What are the common problems of machine-made charcoal machines?

The machine-made charcoal machine is an environmental protection equipment that uses my country’s biomass waste to produce machine-made charcoal. It has high production efficiency and good quality, and the produced machine-made charcoal can be widely used in the market and has been favored by users. Recently, users are operating There are also some failures when the machine-made charcoal machine is made, so what are the common problems of the machine-made charcoal machine? How to solve the common problems of the charcoal machine?

charcoal machines

1. The power indicator of the console does not light up

Reason: ①The power supply of the machine-made charcoal machine is not connected; ②The fuse is blown; ③The indicator light is broken.

Corrective measures: ①Connect the power cord of the mechanism charcoal machine; ②Replace the fuse; ③Replace the indicator lamp.

2. The machine-made charcoal machine motor does not start

Reasons: ①The control button of the mechanism charcoal machine is damaged; ②One phase is missing; ③The voltage and frequency are not consistent.

Corrective measures: ①Replace the control button of the mechanism charcoal machine; ②Connect the power cord; ③Check the voltage frequency.

3. The heating temperature does not rise slowly to 350 degrees

Reasons: ①The power supply voltage of the machine-made charcoal machine is low; ②The resistance heating ring of the machine-made charcoal machine is damaged; ③The model of the machine-made charcoal machine is incorrect when replacing the heating coil wire.

Corrective measures: ① Check the voltage of the machine-made charcoal machine; ② Replace the resistance heating ring of the machine-made charcoal machine; ③ Change the machine-made charcoal machine wire as required.

4. Motor heats up

Reasons: ①The load of the machine-made charcoal machine is too large; ②The two-phase operation of the machine-made charcoal machine; ③The bearing of the machine-made charcoal machine is damaged; ④The air duct of the machine-made charcoal machine is blocked; the ambient temperature of the machine-made charcoal machine is high; ⑥The voltage of the machine-made charcoal machine is unstable; Machine-made charcoal machine rotor winding or indirect short circuit.

Corrective measures: ①Check the supply of machine-made charcoal machine materials; ②Check the machine-made charcoal machine wires, switches, and contacts; ③Replace the machine-made charcoal machine bearings with lubricating oil; ④Remove the machine-made charcoal machine debris and ventilate; Cooling measures; ⑥ adjust the voltage of the mechanism charcoal machine; ⑦ check and exclude.

5. The machine does not produce great

Reasons: ①The raw material humidity of the machine-made charcoal machine is too high; ②The heating temperature of the charcoal machine is low; ③The material is clamped in the spiral groove of the charcoal machine; ④The groove on the heating cylinder of the charcoal machine is misaligned with the groove of the heating cylinder; ⑤The voltage of the charcoal machine is low ⑥The inner sleeve of the charcoal machine bracket is worn; ⑦The inner sleeve of the heating cylinder of the charcoal machine is worn; ⑧The screw propeller of the machine-made charcoal machine is worn.

Corrective measures: ①heat the raw materials as required; ②increase the heating temperature; ③remove the miscellaneous material in the spiral groove of the mechanism charcoal machine; ④reinstall the inner sleeve of the heating cylinder; ⑤check the voltage; ⑥replace the inner sleeve; ⑦replace the inner sleeve of the heating cylinder; ⑧ Repair or replace the screw propeller.

The above are the common problems and solutions in the process of producing machine-made charcoal by machine-made charcoal machines. The machine-made charcoal machine manufacturers recommend that users should maintain them when operating the equipment to avoid its failure. When the equipment fails, It must be solved in time to ensure the smooth production of the machine-made charcoal machine.